Energy-harvesting sensor powered by bridge vibrations

Image: Austroshot/

Unused energy trapped within bridges is to be harvested in an international project led by Heriot-Watt University.

Traffic and wind regularly cause low frequency vibrations to ripple through bridge building materials such as steel and concrete. This energy would normally travel away from its source before dissipating, but academics at Heriot-Watt University in Edinburgh, alongside colleagues from Georgia State University and Georgia Tech in the US, have recognised an opportunity and plan to capture and recycle this untapped source.

They have received £340,000 from the Engineering and Physical Sciences Research Council (EPSRC), part of UK Research and Innovation, and an equivalent amount from the National Science Foundation (NSF) to research and develop a revolutionary vibro-impact energy harvesting device.

Dr Daniil Yurchenko, from the School of Engineering and Physical Sciences at Heriot-Watt University, has created a prototype called a ‘vibrant pack energy harvester’ that can be fitted at multiple locations on a bridge.

‘We are creating a more efficient and cost-effective solution by harvesting energy that would otherwise be lost.’

Dr Daniil Yurchenko, Heriot-Watt University

These autonomous devices, measuring around 5cm to 10cm in length, do not require wiring to an electrical power source. They work by holding a small ball housed within a tube that rolls back and forth as the device absorbs low frequency vibrations. As the ball moves, it impacts on non-conductive materials, known as dielectric membranes, located at either end of the tube. When the membrane is stretched, a brief electrical charge is applied and once it returns to its undeformed state, the generated excessive electrical charge can be harvested.

This electrical energy is stored in a battery and used to power a sensor capable of monitoring the structural integrity of a bridge. Engineers can then record multiple measurements, such as vibrations, traffic load, wind and temperature, all at the same time but without the need for specialist infrastructure to be installed at significant cost.

Dr Yurchenko explained that while dielectric elastomer technology has been tried in wave energy, nothing has been done on such a small scale before: “What we are doing is creating a more efficient and cost-effective solution by harvesting energy that would otherwise be lost. It’s something that has never been done before in this way.

“It’s a technology that can be used on any bridge anywhere in the world. There are plenty of places where these devices can be fitted to a bridge structure such as on cables, on the pillars, other side of the bridge deck, there really aren’t any limits.

Optimising energy harvesting

“The biggest problem in energy harvesting is that the absolute amount of energy produced by a typical device is very small due to the low available level of vibrations. In fact, for the past 100 years scientists have been fighting adverse vibrations to ensure that bridges are safe. So, through this work we will try to optimise the performance of our vibro impact energy harvesting device tuning it to the bridge application.”

The team is working alongside Wenzel Consult, a company that specialises in bridge sensor technology in Austria and Turkey.

As the project advances, the scientists say they intend to carry out real-life testing of their prototype on a 32m long highway bridge in northern Austria.

‘These energy harvesters can be used in bridge damage sensors, minimising sensor maintenance/battery replacement and decreasing the risks to service personnel.’

Professor Igor Belykh, Georgia State University

The multidisciplinary project is due to complete in 2024.

Professor Rachel Kuske, head of mathematics at Georgia Tech, said: “While the device has non-linear behaviour, which is beneficial in generating more energy than is used to power the device, the same non-linearity can result in a range of complex responses to the vibrations.  

“We will use dynamical analyses to predict the different types of responses, as well as to select design choices for responses that optimise energy output. As the bridge vibrations are also inherently noisy, the analysis will also identify how to leverage noise sources that are beneficial and mitigate effects from detrimental noise sources.”

Professor Igor Belykh, co-investigator from Georgia State University, added: “This project seeks to provide guidelines for designing power supplies that can harvest energy from bridge oscillations. These energy harvesters can be used in bridge damage sensors, thereby minimising sensor maintenance/battery replacement and decreasing the associated risks to service personnel on high suspension bridges.”

The scientists said that in the future the same technology could be adapted and used to harvest energy from other vibrating man-made structures and machines.

Story for BIM+? Get in touch via email: [email protected]

Latest articles in Technology